15 miles from our shop in San Dimas. We wire the new-construction mansions replacing 1950s ranch homes in Upper Rancho and Baldwin Stocker — and upgrade the electrical in the originals that are still standing.
Arcadia has two kinds of homes that need panel work: the original 1950s-1960s ranch homes still running on 60-100 amp panels, and the 4,000-8,000+ square foot custom builds replacing them that need 400-amp service from day one. A luxury home in Upper Rancho or Highland Oaks with three HVAC zones, a heated pool and spa, dual EV chargers, a home theater, and a full smart home system can easily pull 300+ amps at peak. We size the service correctly, coordinate with Southern California Edison on the meter and service drop, and pull all permits through Arcadia's Development Services Department.
Arcadia has over 110 public charging stations citywide, but when you have a three-car garage in Baldwin Stocker and two Teslas in the driveway, you need home charging. We install Level 2 chargers with dedicated 240V/50A circuits — one per vehicle if needed. Many of Arcadia's luxury homes have the panel capacity for it already, but the older homes that haven't been torn down yet usually need a panel upgrade first. We handle both in one project, one permit through the city. For new construction, we design EV-ready circuits into every garage bay from the rough-in stage.
Arcadia is one of the most active tear-down rebuild markets in Southern California — the city sees dozens of older homes demolished and replaced with new custom construction every year. These new builds are typically 4,000 to 8,000+ square feet with sophisticated electrical demands: multiple sub-panels, dedicated circuits for every major appliance, structured wiring for networking and audio, landscape lighting on its own panel, and whole-house automation systems. We handle electrical from rough-in through finish, coordinating with your general contractor and the city's plan check timeline.
The new-construction homes going up across Arcadia aren't just big — they're loaded with technology. Lutron and Control4 lighting systems, whole-house audio zones, motorized shades on every window, security cameras on every corner, and centralized home automation racks that need dedicated power and ventilation. All of this runs on clean, properly sized electrical circuits and structured low-voltage wiring. We install the infrastructure that makes smart home systems work reliably — dedicated circuits, isolated grounds for sensitive electronics, and properly labeled panels so your automation integrator can do their job right.
Arcadia properties — particularly the estates in Santa Anita Oaks with lot sizes up to 40,000 square feet — have extensive landscape and exterior lighting needs. We install LED path lighting, architectural uplighting, security floods, and decorative fixtures across large properties. Inside, we do recessed lighting layouts, chandelier installations, under-cabinet LED, and dedicated dimming circuits. For the older Arcadia homes still on original wiring, we add outlets, upgrade two-prong ungrounded receptacles to proper GFCI circuits, and bring kitchens and bathrooms up to current code.
We're 15 miles east in San Dimas — about 18 minutes on the 210. When a breaker trips and won't reset in your Highland Oaks home, or a construction site in Santa Anita Oaks loses power mid-build, or an overloaded panel in an older home starts smelling like burnt plastic — call us any time. Arcadia's San Gabriel Valley heat regularly pushes old electrical systems past their limits between June and October, and the newer mega-homes can trip breakers too when every system is running at peak on a 105-degree day.
Arcadia isn't like other San Gabriel Valley cities. With a median home price pushing $1.8 million, a median household income above $116,000, and one of the most active tear-down rebuild markets in LA County, the electrical work here is fundamentally different. You're not just swapping out a panel in a 1,400-square-foot ranch home — you're wiring a 6,000-square-foot custom build from the ground up, or upgrading a mid-century original to handle modern loads before it eventually gets replaced too.
We understand both sides of Arcadia's housing stock. The original homes built in the 1940s through 1960s — in neighborhoods like Santa Anita Oaks and the streets south of Huntington Drive near the Arboretum — have the same aging wiring, undersized panels, and aluminum branch-circuit issues you find across the San Gabriel Valley. But the new-construction mansions going up north of the 210 in Upper Rancho and Highland Oaks need a completely different skill set: 400-amp service, multiple sub-panels, structured wiring for automation, and electrical plans that pass the city's plan check on the first submission. We do both, and we do them right.
Arcadia has experienced a massive wave of tear-down rebuilds over the past two decades — older 1,200-1,800 square foot ranch homes from the 1940s-1960s demolished and replaced with 4,000-8,000+ square foot custom mansions. The electrical difference between these two homes is enormous. The original had a 60-100 amp panel, a handful of circuits, and maybe 30 outlets in the whole house. The replacement needs 400-amp service, 40-60 circuits, hundreds of outlets and switches, dedicated runs for HVAC equipment, pool systems, EV chargers, and a full smart home backbone. If you're planning a tear-down rebuild, the electrical design needs to happen during the architectural planning phase — not after framing is done. Getting it right from the start saves time, money, and prevents the kind of change orders that delay construction and blow budgets.
Arcadia's electricity is generated by Clean Power Alliance (CPA), a nonprofit joint powers authority that the city joined in 2018. Southern California Edison still delivers the power, maintains the grid, and sends your bill. For homeowners, this matters when you're doing a panel upgrade or new service installation — the coordination is with SCE for the meter base, service drop, and final connection, even though CPA is technically your generation provider. For new construction, SCE has specific requirements for service entrance equipment, meter placement, and conduit sizing that need to be right before they'll energize the panel. We handle all of this coordination so you don't have to sit on hold with the utility.
A standard 200-amp panel is fine for a typical three-bedroom house. But Arcadia's new-construction homes are anything but typical. Here's a rough load calculation for a 6,000-square-foot home with the amenities that are now standard in Upper Rancho and Baldwin Stocker: three 5-ton AC units at 30-40 amps each (90-120A total), a pool and spa heater at 50A, two Level 2 EV chargers at 50A each (100A), a home theater at 20A, kitchen appliances on dedicated circuits at 60A, and general lighting and outlets at another 60-80A. That's over 380 amps before you add the security system, landscape lighting, motorized gates, and automation equipment. This is why 400-amp service — or even dual 200-amp panels — is the starting point for serious Arcadia builds. We load-calculate every project to NEC standards and make sure the service matches the demand.
We're 18 minutes away in San Dimas. Call for a free assessment on any residential, commercial, or new-construction electrical project in Arcadia.
Call Now: (909) 526-1355 Request a Quote Online